Kids and Cars - Driving Is More Hazardous When School Is In Session

The new school year has started. That means a lot more traffic on the roads, and a lot more kids crossing streets, parking lots and driveways. Parents drop off their children at school in the morning and pick them up in the afternoon.
And little does anyone realize the dangers.
With today's prevalence of SUV's, Minivans, and sedans with high back ends, visibility behind these vehicles is seriously compromised. When mom or dad puts the car into reverse, they are taking it on faith that whatever is behind the car will get out of the way.
Automobile manufacturers are dealing with this safety problem by offering (on select high-end models) a device designed to help a driver when in reverse. These little electronic marvels, often called Reversing Aids or Backup Sensors, can literally be lifesavers.
Ask Dr. Greg Gulbransen.
On October 19, 2002 Dr. Gulbransen was backing his SUV into his driveway when he ran over his 2 year old son Cameron.
If Dr. Gulbransen would have been aware that something was behind him -- whether it was something as precious as his son, or as trivial as a mailbox -- he could have stopped the car before a tragedy occurred.
If you've never seen or used a reversing aid, you might be surprised at how technically advanced they actually can be.
Reversing aids use a variety of technologies to sense an object behind the car. Some units use Doppler radar, and others use infrared sensors, but by far the most accurate method of detection is the one the U.S. Navy uses on its submarines: sonar.
Sonar can operate in any weather, including direct sunlight or rain. And it doesn't require that the car be moving in order to sense an obstruction.
And that's when the device has to warn the driver.
Some of the least expensive models use a tone which beeps more rapidly as you get closer to an obstacle. Although you have no real indication of how far you are from an object, you can at least hear the relative distance just by listening to the beeps. Compare that to other devices which actually have LED displays on your dashboard. These are cumbersome -- almost useless -- because when you drive in reverse, you naturally look behind you, and you'll never see the little red lights.
That's why an audible sensor is best. But even better than a beeping indicator is one that tells you in a spoken voice exactly how far away you are. Not only do you not have to look forward at your dashboard, you'll know without guessing how much further you can safely back up.
When buying a new car, ask your dealer if a backup sensor is available for your model. If a new car is not in your plans, then search Google or your favorite search engine for Backup Sensors or Reversing Aids that you can add to your car.
Another valuable resource is the Technology page at http://www.KidsAndCars.org, a non-profit organization dedicated to children's safety in and around automobiles. Janette Fennel, who runs the organization, has compiled a list of different reversing aids.
She's a big fan of these devices.
Ms. Fennell is also a champion of children's safety, and is responsible for proposing much new legislation in this area, including the recently proposed legislation H.R. 2230, the Cameron Gulbransen Kids And Cars Safety Act of 2005, which has also been supported by the American Academy of Pediatrics.
The bill would require that the Department of Transportation establish regulations and deadlines by which light vehicles "would be equipped with a variety of safety measures, including a rear-ward visibility standard and driver notification systems", says Ms. Fennell.
This type of legislation is a necessary stepping stone in order to strengthen car safety codes throughout the country.
Whether or not you have children, think carefully before backing up. When you buy a new car, ask the dealer if a reversing aid is available for your model. If not, consider adding one to your current car.
Even if you don't have kids, or if school is not in session, it's worth the peace of mind.
Just ask Dr. Gulbransen.

by: Jerry Appleby

Read More......

Keeping used motorcycle parts as good as new

Even with regular maintenance and upkeep, our motorcycles tend to get used and subjected to different elements in the environment. To keep used motorcycle parts as good as the day when we first bought them, regular washing and rinsing will do the trick.

But you should take note how you do your washing. You might scratch parts of your motorcycle.

Top Rule: Avoid scratches.

Scratches are the biggest enemy of any bike's finish. The secret of keeping your used motorcycle parts as good as new is to avoid scratches in your motorcycle. Dirt and grime when rubbed in while washing or drying, act as sandpaper and will definitely dull the brilliance of your bike's paint.

To avoid scratching your bike, first, you need to remember that anything that comes in contact with your motorcycle's finish should be made of soft material. Take care that no harsh or rough surfaces will be able to connect with any part of your motorcycle. Zippers are the worst offenders.

Use only clean, freshly washed cotton cloths or towels to dry your bike after washing. When you need to put on any application to make your bike shine, again use the clean cotton cloths and towels. Rinse thoroughly the sponges or wash mitts, as well as the bucket, before and after washing your bike to remove any dirt or grime.

One of the best advice I got from a used motorcycle parts site was to separate my bike's areas into normal and rough areas when washing. I usually consider the painted surfaces as normal areas, while the tires, engine, and inner fenders are the rough areas. I use different wash mitts and sponges for each area to keep dirt and grime away from the sensitive areas. This way, scratching would be avoided.

Use also a gentle stream of water when rinsing, rather than high water pressure that comes from the hose. The high pressure of water will cause dirt to grind further into the paint, causing scratches along with other worse problems. And remember to use generous amounts of water when rinsing. Dirt that causes scratch will easily float away with enough water used.

When washing your bike…

Use lots of water, but without the high pressure. Totally avoid using pressure washers. Instead let the water flow freely by detaching the nozzle from the hose.

Along with the generous amount of water, use detergents designed specifically for motorcycle washing. Ordinary detergent tends to remove the wax that we want to try to keep. Simply mix the detergent according to the directions and go for it. Just make sure you rinse each section soon after applying the detergent so that no soap film will develop. It is difficult to get rid of the soap film when it dries up.

After washing, rinse, rinse, and rinse some more. Rinse everywhere. Every nook and cranny should be rinsed of soap.

Lastly, wash your motorcycle without bright sunlight. Soap suds can easily dry from the heat. Ideal time of the day would be in the late afternoon or early morning when the sun is not so strong.

by: Granny's Mettle

Read More......

Is Your Car A 'Lemon'?

Sooner or later we all must buy a car. And when we can, we buy them brand new.

However, most of us are stuck having to a buy a used car from a dealer or private party at some point. The downside to this is that you can get a car that at first seems like everything you ever wanted, but soon becomes your worst nightmare.

What I have come to learn is that by the time that you begin to realize that you have a lemon on your hands, it is usually too late. The car has already outlived its 90 day warranty which is often filled with loopholes for the dealer anyway. What does this mean for you? If you're like most people, you're thinking to yourself, "it means you're screwed." However, read on.

Most people who buy their cars used know that dealers set up their agreements in terms that will serve only their best interests. Buyers also assume that there is really nothing that they can do in order to get the most out of their money.

But that couldn’t be further from the truth.

In fact, there is a lot that you can do to protect yourself even after you have bought yourself a lemon.

That’s right: as a buyer you do have rights as well.

In fact, there are laws that are designed to protect you should you find that you get stuck with a bad car and a terrible dealer.

Did you know that now is the best time to buy a car? There are very large cash rebates, dealer discounts and employee discounts offered just about everywhere.

The recent major drop in the car industry had forced many people to steer away from buying new cars and also has prompted some of the best discounts ever from the dealerships. You need to do some online research before hitting the dealership and it could save you money and headaches.

Websites like Autoweb.com, Edmund's Automobile Buyers Guide, Autolink, Autopedia, Kelley Blue Book and CarPrice.com are just some of the sites that are currently giving up to date pricing information on new cars.

You should however make note of the dates when each rebate is set to expire so that you can take advantage of these special offers.

When you are looking for the best prices, you want to visit several different Web sites when researching pricing information for the obvious reasons.

Everything from sticker price to customer rebate information may vary from site to site. It's wise to cover all the bases. Whenever you are in doubt, contact an auto manufacturer directly.

When it comes to the basics behind the lemon laws, knowing the basics can be the difference between whether or not you get screwed or get the chance to recover the money that you spent on the car.

The state and federal statutes offer a wide array of relief for consumers who get stuck with a bad car or truck after they buy.

At the same time, these statutes provide buyers with the chance for recovery of costs and attorney fees which are a strong incentive for attorneys who would like to take up the cause on behalf of unhappy lemon owners.

"Lemon laws" basically outline all of the procedures that are used in order to settle these sorts of new car problems.

These lemon laws differ from one state to another, but lemon laws in general are designed to provide the owner with a refund or replacement vehicle should this problem occur.

For example, some states mandate a refund or a new car if a large enough problems cannot be repaired within four tries, or if the car has been out of service for around a month within the first year or 12,000 miles driven.

However, there are some exceptions to this rule, such as; some states only provide you with the chance to make one attempt for significant safety related issues such as the brakes or steering.

Some states do not even stop with just providing lemon owners with either a refund or a new car. Some of them will, in fact, also let you recover any sort of attorney's fees that you have to deal with during your pursuit of getting some satisfaction from your purchase of a lemon.

It is always good to know that you can get some sort of return on your money when you buy a lemon. It happens so often that eventually there was bound to be some laws protecting the buyers.

What is sometimes sad about the lemon laws is that they do not necessarily help you. It all depends on your specific situation.

by: Ted Rossio

Read More......

How to Transport Your Classic Car.

Classic car transport is a large branch of car transport; it is a specialized field that includes car transport companies that are dedicated to the transport of antique and vintage cars. Most trailers used for the safe and efficient transport of classic cars are specially designed for smooth travel and protection from road and weather.

Classic car transport companies usually employ only professional drivers who are experienced handlers of antique and exotic cars. Some popular trailer options for secure classic car transport are: six-car enclosed trailers, four-car enclosed trailers, and two-car non-stacking enclosed trailers. Most auto transporters of classic vehicles will offer delivery from door-to-door or delivery to the customer. Most classic car transport companies will accept non-running vehicles.

When you are searching for a classic car transport company, ask if classic and vintage vehicle transport is their main activity or a sideline of another business. In addition, find out if they contract out transport to third parties. Make sure when you are investigating car transport companies that classic vehicles are their main focus. To safeguard your interests, also make sure they carry the best insurance coverage available.

Many classic car transport companies will design an itinerary exclusive to you, this allows for greater flexibility on times of pick-up and delivery. Additionally in-transit contact between office and drivers through cell phones is a service that most classic car transport companies will provide as part of the basic transport service. Winching is also available at a modest fee.

Many classic car transport companies offer worldwide vehicle transportation solutions to individuals. These classic car transport companies specialize in reliable, proficient service with frequent departures from major U.S. ports. Normally you will be assigned a very experienced customer service representative to insure the safe convey of your car.

Classic car transport companies use various methods to move your car long distances, such as flatbed truck, enclosed single trailer and enclosed rail service. Your car will probably travel flat without being tied down by chains. Easy and safe loading on custom built covered trailers with full lift gates is usually a standard and most classic car transport companies have tie-down systems that provide security without harming your vehicle. Airtight sanitary environments and full air equipment for smooth travel are other popular available options. Custom equipment designed to meet your needs is often available upon request.

It should not be difficult to find a classic car transport facility with a professional crew of mechanics and maintenance people who maintain an exceptional fleet of opened and enclosed transports to fit your needs and budget. Just knowing the basic facts about classic car transport will make finding the best company a sure success.

by: Thomas Morva

Read More......

How to Start Your Search for the Perfect SUV Accessory

You finally did it. You went out and bought the SUV that you have always wanted. So now, you can see over the cars next to you at the intersection and you don't really have to worry about the idiot in lane next to you on the cell phone, after all, you can roll right over him. Now what? You want to personalize your SUV, make it reflect who you are, right? Right, you need SUV accessories. There are so many to choose from, where should you start?

1- Price is often a first consideration for many SUV owners. Quality is the second. These are the reasons that the internet is a good place to start looking for SUV accessories; there are so many sites and products to choose from. Consumers today are much more conscience when it comes to getting what you pay for, or even, getting more than what you pay for. Owners of SUV's are just like anyone else, they like to get a good product at a great price. The competition is so fierce that most sites will offer free shipping or deep discounts to win your business.

2- Companies that specialize in aftermarket add on parts are a great way to get your hands on the actual part that will be installed on your vehicle before you actually purchase it. SUV owners are also very fussy about the accessories that they choose to add to their vehicles. What ever is being replaced needs to be perfect For example, if you are looking for a set of running boards for your truck, you probably know pretty much what you want them to look like installed even before you begin your search. This is true not only for something that stands out, like running boards, but also for smaller items such as custom knob covers for the interior of the vehicle.

3- The dealership where you originally purchased you SUV is also an excellent source for quality aftermarket accessories. Dealers tend to be more expensive than some other sources of parts, and they may offer a more limited selection, however, the parts they do handle will be genuine accessories for your particular SUV. If they don't handle these types of products, they can give you the name of a reputable accessory dealer in your area.

4- Swap meets can be a fun, unconventional way to get the parts you are looking for. This is especially true if you are searching for an accessory that is hard to find or that is no longer being made. A swap meet allows you to see the part and get some of its history before you buy, since the part will most likely be used, this information can be important in your decision.

5- If you are the more adventurous type of buyer, you might want to try online auctions. Online auctions allow you to do business with people from all over the globe. There are many auction sites, with out a doubt; you will be able to find the part you are seeking. The biggest draw backs to buying from an online auction is the gamble that is involved (that may also be a lot of the allure as well), unfortunately you never really know if the person on the other end of the computer is trustworthy until you receive your part in the condition it was described. Fortunately, most online auction participants are trustworthy and understand that that is why they have customers.

by: John Mancini

Read More......

How To Save Money On A New Car

The price of cars these days is just out of this world. You can figure on spending upwards of $30,000 for a family van. No wonder a lot of people are opting for used cars. Even with prices creeping up and up there are still ways for you to save money if you have your heart set on a new car.

The first advice I'll offer is to do your homework before you approach a dealership. There is an endless amount of information available on the internet. Every car manufacturer has a website, dealerships have web sites. See what deals they are offering on what models. Check on the edmunds.com website for information on retail prices for new and used cars of any make and model. You should, before you even pull into the dealership, have a ballpark figure of what your new car should cost, including any special packages you may want.

A lot of dealers have taken the haggling and pressure out of new car buying, which many of consumers like. Remember the days when you'd ask what the price of a car is and the salesman would reply "how much can you afford to pay a month?". You never knew exactly what you were paying for your new car until you were at the desk ready to sign the contract. Today we are educated consumers and those days are gone forever.

You will be able to get a good deal during the end of model year sales. The dealers will make just about any deal to get an older model off the lot to make room for a new one. Also, go into the dealership at the end of the month. Your salesman will be doing his best to sell a few more vehicles to up his commission payment.

Get the bottom line price for that new car before you talk about a trade in. Generally the first thing a salesman will ask is if you have a trade in. Say "no". If your salesman knows you have a trade in it will affect the price you pay for your new car, no doubt. If he makes you a ridiculously good deal for your trade in you can believe that the price of your new car will reflect this. Make sure you know what the value of your trade in is. Again you can check edmunds.com. Take you car to a variety of dealerships and get an idea of this price from them.

The bottom line is to do your homework. Get a price for the new car from several different dealers. There is nothing wrong with each of them vying to give you the best deal.

Consider your finance charges. Get a quote on the interest rate you're offered from the dealership, then check with your bank or credit union to see what type of interest rates they offer.

by: Shaan Randow

Read More......

Pssst: Wanna (not) Buy a Stolen Car?

Would you buy a used car--with cash--from someone you just met in the bar, and who walked you down a dark alley to show you the car? Not likely. How about from a well-dressed, friendly, middle-aged man or woman, who placed a classified ad in your local newspaper, and who meets you midday at a restaurant of your choice?

Oops! You may be more likely to be cheated by seller number two. That's the story of Jennifer Warwa, who bought a minivan and had her mechanic examine it. The mechanic later said how shocked he was that Jennifer had been scammed:

"Because I met the gentleman who was selling the vehicle. Very clean cut. In his fifties. Very soft spoken.... And he went with her to get it inspected. There was just no sign that was the kind of person he was" the mechanic told CBC's Marketplace.

A few months later, Jennifer got a phone call from the police. They said she had purchased a stolen minivan, and they were coming to seize it. She was so upset, she tried to hide the van from the police. Eventually they caught up with her and she ended up paying for a year and a half for a $5,000 bank loan on a van she could not drive. Ouch!

Jennifer was just one victim in the chain that included the original owner, the insurance company, other consumers whose insurance rates keep rising, and the police, who spend thousands of hours tracking thefts. According to the FBI, a vehicle is stolen about every 25 seconds in the USA, amounting to an $8 billion yearly problem.

Here's how these scams often work. Thieves target particular cars: for their value, their ease of resale as a whole or in parts, or because they are easier to steal. Years ago, most cars were stripped for parts, including unusual parts such as airbags. But today some thieves are so brash they sell cars through newspapers.

This newer scam is called "VIN cloning", because the Vehicle Identification Number is stolen from another car. Criminals obtain VINs by copying them from the dash of cars in parking lots--even at dealerships. Some even physically remove the VIN plate from vehicles in auto salvage yards that allow customers to "pick your own parts." (They do not mean that literally!) The number is used to falsely obtain new ownership documents, or documents are forged. Either way, a cloned VIN allows them to transform stolen cars into pseudo- legal vehicles that can be officially titled and sold. Many thieves work across state lines: cars may be stolen in the East, registered in the Mid-West, then sold in California. Scary!

Here's what you can do to avoid buying a stolen car:
** Check the VIN on the dash against the VIN in the driver's door jamb, under the hood, and on the paperwork
** Use the VIN to get the car's history at carfax.com for about $20
** Ensure title and registration documents match the name and address of the seller
** Is the car from out of state?
** Be suspicious if you must meet a private seller in a parking lot. Better to see that they live at the address where the car is registered
** Has the vehicle recently been transferred?
** Does the seller use a home or work phone number, or just a cell?
** Is the selling price oddly low?
** Be warned that some used car dealers are getting scammed, too
** Pay by certified cheque or money order, not cash.

Keep in mind that most private sellers are not thieves, but rather honest, regular folks like you. And prices do tend to be lower with private sales. So if you follow my advice, you can greatly improve your chances of driving away with a "genuine" used car.

by: Michael Trusthold

Read More......

Proper installation of used motorcycle cables

Part and parcel of owning a bike is maintaining its appearance and its capability. Nevertheless, despite making sure that the parts and cables of the motorcycle give us maximum service, we cannot but accept that they have their own warranties and lifetimes.

Unlike artwork or antiques, motorcycles are made to be used and abused. With all the elements found in the environment, motorcycle parts will definitely have its final day. When that day comes and you don't have enough money to buy new ones, why not settle for used motorcycle parts, e.g. cables? With a few tinkering and proper installation, they might just provide you the service you need in many years to come.

Here are some suggestions for proper installation of used motorcycle parts and cables:

Tip #1: Inspect and make sure you have the correct cable. This is the very first step in getting the best used cable you need. Inspect the used cable for any major wear and tear. Remember that these are used cables so it will definitely have a few scratches; but it must not be too great that using it for just a few days will result in a total bust. After you have checked thoroughly, make sure you have the correct part for the application, e.g. correct cable ends, proper size casing ferrules, correct size, shape and thread size of adjusters/elbows, etc.

Tip #2: Make sure all adjusters are in "closed" position.

Tip #3: Use a direct route for the cables. Route your used cables from control to actuator in the most direct way possible. Keep cables away from hot surfaces and avoid sharp bends, as well as "kinks" in the housing or inner cable.

Tip #4: Adjust throttle/idle cables. These should be adjusted the carb/s will return to full close when off. Adjust any excessive freeplay and be sure throttle action is smooth and free from open to full close before starting the engine. Also make sure that the used cables do not bind together or hang up when there is full lock-to-lock movement of bars.

Tip #5: Make sure clutch/brake cables are routed properly. This is to avoid binding or hanging up the cables when there is full lock-to-lock movement of bars. Also, cables that are routed properly will not bind during compression of forks or suspension. Install lever and actuator fittings, adjust freeplay to correct specs and check for smooth-positive action. These are done before starting the bike.

Tip #6: Route the speedometer/tachometer cables using a direct path. Make sure that the cable will not hang up on the caliper when forks compressed on the front wheel drive speedometer cable. This is what usually happens with aftermarket calipers because they often come in a larger size or different shape. Always make sure that the inner cable is well-lubed with light grease when installing and removing. Clean and re-grease regularly for maintenance.

Tip #7: Avoid having contact with painted surfaces when installing stainless steel braided cables. The braided surfaces of these used cables are very abrasive. You can use shrink or spiral wrap and/or cable guides when needed. And because stainless braided cables are less flexible, always keep this in mind when getting measurements for applications that are tailored according to your specifications. Clean and lube like any conventional cable assemblies.

And like any other used motorcycle parts, keep used cables clean and properly lubricated when necessary. Always check on the proper adjustments and inspect for any wear and tear on a regular basis. Signs to look out for are torn or worn housing, frayed wires, and signs of bending or kinking at the controls.


About the author:
Granny's Mettle is a 30-something, professional web content writer. She has created various web content on a diverse range of topics, which includes digital printing topics, medical news, as well as legal issues. Her articles are composed of reviews, suggestions, tips and more for the printing and designing industry.

Her thoughts on writing: "Writing gives me pleasure… pleasure and excitement that you have created something to share with others. And with the wide world of the Internet, it gives me great satisfaction that my articles reach more people in the quickest time you could imagine."

On her spare time, she loves to stay at home, reading books on just about any topic she fancies, cooking a great meal, and taking care of her husband and kids.

by: Granny's Mettle

Read More......

Preventative Car Maintenance and Fuel Filter Replacement Tips

As with health care, preventative car maintenance is the best thing you can do for those dependable vehicles that get you where you want to go everyday. With preventative car maintenance you might invest a little here and there, but in the end, you will always save yourself time, money and the aggravation that comes with ‘break-down’ surprises. Listed below are some additional reasons to get serious about preventative car care:

• Safety is the #1 reason to invest a little of your hard earned dough in preventative car maintenance. Vehicles that are poorly maintained make it that much easier for you or one of your family members to get in an accident.
• Increased performance. A well maintained car means improved fuel economy as well as a car that is easier to operate.
• A well maintained car will also improve the trade-in or resale value of your vehicle.
• Dependability and easy handling. A well maintained car means that you won’t have to worry about incorrect wheel alignment, worn tires and worn suspension components.
• Pride. Many people agree that your car definitely represents a certain extension of your own personality. Take car of your car!

Establish Car Maintenance Habits
It is fairly simple to get into the habit of getting your oil changed every three months but it’s a bit more difficult to make those yearly check ups and replacements that every car needs. You should, on a regular basis, (meaning annually or at least every two years) ask your auto technician about the status of your air cleaner filter, oil filter, air cleaner, air filter kn and your fuel filter.

Common Complaints that Can be Solved with a Fuel Filter Replacement
This article focuses on fuel filter replacement because experienced mechanics find that many people frequently complain that their vehicles are ‘experiencing’ power loss, hard starting, or hesitation.1 These problems are in general due to clogged fuel filters and can easily be avoided with a simple (http://dakotafilterservice.samsbiz.com/page/17tbb/Home.html) fuel filter replacement.

How Often Should You Change Your Fuel Filter?
As mentioned above, it is recommended that you change your fuel filter on a yearly basis. However, a yearly replacement only applies to high mileage vehicles. Those of you who use your vehicles only on occasion or only drive short distances on a daily basis, then you can probably get away with a filter replacement every two or even three years. If you have questions in regards to your vehicle, ask an (http://dakotafilterservice.samsbiz.com/page/17tbb/Home.html) experienced filter specialist how often you should change your fuel filter.

Don’t Fall For It!
Many new vehicles supposedly are equipped with a ‘lifetime’ fuel filter that the manufacturer claims will never have to be replaced. These newer vehicles may require a fuel filter replacement only every other year, but they will indefinitely have to be replaced at some time. Any fuel filter (including the new ones) can clog or be exposed to moisture and rust--so don’t fall for the lifetime fuel filter story.

Fuel Filter Replacement Services
You can replace your fuel filter by yourself, but today when there are literally dozens of service stations at your disposal, you will find that you will actually save more time and more money if you do your shopping right the first time. Take time to shop/compare and even ask for references. If you take the time now, it is unlikely that you will regret your decision later. Also, if you do decide to change your fuel filter by yourself, make sure that no one smokes around you as you work. Changing a fuel filter can be extremely dangerous.

Choose a Better Fuel Station?
Also, to prevent the quick ‘decay’ of your fuel filter you may want to consider patronizing only those fuel stations which have fuel filters within their gas pumps. These filters assure that the fuel you put into your vehicle will go through one final ‘filter session’ before going into your car. You would be surprised at the amount of dirt and other junk that is prevented from going into your vehicle because of fuel station pump filters.

1It’s simple science; a clogged fuel filter cannot allow the same amount of fuel to flow through it as a newly replaced one. This may mean that on roads around your home--as you drive slowly--your car will respond well, but at highway or freeway speeds your car may splutter and lack power.

by: Boyd Norwood

Read More......

Prepare Your Ford Escape For a Summer Escapade, Use Top Quality Parts

Taking your family or friends for a long ride with your Ford Escape—away from the busy city streets—would be a perfect way to spend the hot summer days and of course, to test this SUV’s performance. Ford Escape is an entry-level Sport Utility Vehicle, and although positioned a rank lower than the best-selling SUV, the Ford Explorer, it offers a respectable line of performance auto parts, impressive power and remarkable rugged looks. In 2004, a hybrid Escape model was launched, giving Ford the pride of introducing the first Sport Utility Vehicle to use hybrid technology. The 2004 Ford Escape Hybrid was proven to be 75% more fuel efficient than the other Ford Escape models and other SUVs as well.

You must be excited driving the Ford Escape for your adventure, but before you head for fun, make sure your vehicle is equipped with the necessary auto parts and accessories to ensure your convenience, comfort and most especially, safety. Whether you are driving a Ford Escape or not, you must do a regular checkup on your auto to ensure it’s always at its best shape and driving condition. Although built with Ford’s high quality standards, Ford Escape Parts are also subject to common car problems, especially when it is not given enough care and attention.

If you want your vehicle to work at its best, don’t let small problems pass without fixing them. They can be a big source of stress and great financial burden, too. But don’t worry because the friendliest and most comprehensive Ford Parts Discount store offers excellent quality replacement Ford Parts at very reasonable prices. Ford Parts Online now features updated inventory of the most dependable Ford performance parts, Ford body parts and even Ford accessories. If you are thinking about buying Ford Parts Used, think again. You can now buy original top quality Ford parts at exciting deals easy, fast, conveniently and securely online.

Here are some insights that can help you prepare your vehicle for a long ride and some tips on car maintenance. Replacement and aftermarket auto parts mentioned can be found at Ford Parts Online, the most experienced and trusted Ford Parts Discount store:

1.Ford Wheels are the closest to the road, so they are more prone to wear and tear. Always wash your Ford Wheels with soap and water to prevent corrosion. Likewise the tires must be properly scoured to remove deep down grime and small particles it came contact with on the road. If you notice serious problems, don’t hesitate replacing them. It’s better to spend extra amount for a new wheels rather than suffer the inconveniences of a road accident.

2.Traveling during the hottest days of the year could be wearisome if your air conditioning system isn’t working. Check the major parts of your a/c system, especially the Ford AC Condenser, which is the one in charge of cooling off the refrigerant gas that absorbed the heat from the cabin. Check if the condenser has leaks; the refrigerant gas could freeze anything it contacts and could suffocate when inhaled.

3.Check the electrical system; especially, check your Ford Alternators and test the battery. Without these two essential parts of the system, your car won’t run. Make sure your battery and the alternator are free from damages.

4.Replace busted Ford Fog Lights. Driving without sufficient light especially at night is extremely dangerous. When driving off-road, you may need additional auto lights for added safety.

5.Lastly, don’t forget to check the engine, fuel and the fuel filter to avoid breakdowns and roadside delays. Clean filters could help you improve the vehicle’s performance and help you save on fuel expenses.

For proper maintenance of your Ford Escape Parts, you can consult the Ford car experts or Ford-trained technicians. Ask you dealer about their repair and maintenance services. Meanwhile, for your best replacement Ford Escape parts and other Ford auto parts needs, you can count on Ford Parts Online.

by: Jay Stevens

Read More......

Planning A Car Audio System Installation

With such a wide range of components and gadget on the market for car audio systems, the big question is "Where do I start?"

First you must decide what exactly you wish to do. If you are wanting to build a car audio system for a daily driver (the car you drive back and forth to work) with good sounds, but you are not interested in competing, a system can easily be put together for under $1000. However, if you are looking for the all-out bass monster, be prepared to drop in some big bucks into your system.

One of the most important things to keep in mind when building a car audio system is planning. Get an idea of where you are going to place components, subwoofers, amplifiers, and power distribution. A lot of headache can be avoided with the proper planning!!

For the basic system, lets look at some of the components needed.

Let's first start with the head unit (CD player). Obviously you are going to want a nice head unit. If you start with a good quality cd player, and choose to upgrade your sound system in the future, purchase a head unit that will grow with you. Some of the features you may want to keep in mind are:

1. CD changer controls

2. XM / Sirius controls (if you decide to add Satellite radio in the future)

3. Dual RCA outputs (carries signal to the amplifiers)

4. Pause button (important for competing)

5. Detachable face, or other security devices

6. High voltage line driver - this will send the sound signal at a higher voltage to your amplifier/s reducing noise and improving overall sound quality.

After you have chosen your head unit, you will want to make a decision on amplifiers and subwoofers. Keep in mind that you get what you pay for. A $30 subwoofer will be as big as a $300 subwoofer, but the capacities of each will differ greatly. Look at the power handling of each subwoofer and decide accordingly. You will want subwoofers will work with your amplifier/s (see compatibility).

You must also keep in mind the available space in your vehicle. Are you willing to give up your entire cargo area? How many subwoofers will fit? Decide on the size. Sizes will vary from 8" up to 18", some are square (Kicker), but most are round. Also keep in mind the resistance (ohms) of the subwoofer and make sure they are compatible with your amplifier/s (see compatibility). The subwoofer decision will also have an effect on the enclosure you decide to build or buy. For the basic system, I would recommend purchasing a pre-fabricated subwoofer enclosure. This will save you a bit of money and headache (especially if you end up building it two or three times!!). Make sure you take accurate measurement of your cargo area before building or buying an enclosure!!

Other components may be needed depending on the type of system you are building and how elaborate you want your sound to be. For the competition vehicle, figure on upgrading your alternator, adding a battery to your system (maybe more), running high quality RCA cables, power cables, ground cables, and speaker cable. You may need to add a capacitor to provide your amplifier with a reservoir of power for bigger hits from the subs. You may need an electronic crossover, an equalizer, replacement factory speakers, an amplifier for your mid-range and tweeters, additional speakers within your vehicle for staging, etc.

by: Will Reece

Read More......

Oil – The Life Of Your Car

Oil cleans your car. It lubricates parts. It helps cool things down. Without it, your engine would be sitting squarely in the center of your local junkyard.

Scheduling regular oil changes is vital to the life of any vehicle.

The oil filter keeps little bits of dust and other contaminants out of your engine, and helps ensure the oil runs smoothly, so you want to change that every time you change the oil.

Imagine how your body would react if your kidneys and liver shut down. The impurities in your blood would build up continually, and it wouldn't take long for your body to completely break down.

Oil for your car can be likened to blood to your body. Your car needs clean oil to keep going. What would happen if you never changed your oil?

Well, you'd be lucky to get 30,000 miles out of the car before your engine would collapse.

Say you only change your oil once a year. Your car seems to be running fine, so no harm done, right? Not so fast! Your engine has been flooded with contaminants. It won't be long till you find yourself coming to a standstill.

Regular oil changes are as important to your car as daily trips to the bathroom are to you. Now, we won't take the analogy too far, but you get the idea. This one scheduled maintenance may help your vehicle avoid mechanical failures.

I actually heard two mechanics say that they figured you could run a car forever if you had the oil changed every 2000 miles. That may seem excessive to some folks. But it kept my baby humming nicely!

Now if you see any hint of an oil leak on the driveway after the car is parked, get to a service station. This could be ultra bad news and you need to have your car checked out immediately. Ditto if you detect a burning smell or smoke coming from around the engine!

You may not feel 100omfortable changing your oil, but you can check it easily. It's best to check the oil when your engine is cold. Unscrew the cap and pull out the dipstick. Wipe it with a clean tissue or paper towel. Reinsert the stick all the way. Then pull it back out and check the dipstick. You'll see "add" and "full" lines clearly marked on it. If the oil film is between the "add" and "full" lines, you're good. If it's below the "add" line, you need a quart of oil. Make sure you use the kind recommended in your owner's manual. After adding the oil, repeat all the steps.

See, that wasn't too hard, was it?

Make sure you take the time to check the oil levels in your car, and have it changed regularly. It literally means the difference between life and death for your vehicle!

by: Samuel Murray

Read More......

OEM-quality Ford Focus Parts Available at Top American Ford Parts Dealer

“It begs to be driven,” says Ford. Beyond doubt, this car is very inviting. It appeals to a lot of buyers not only because of its modern styling and excellent driving abilities but most especially, its reasonable price.

Now on its sixth year, Ford Focus remains to be a strong contender in the economy car class in America and in United Kingdom. Since its debut in 1998 (in UK), Ford Focus has garnered over 60 awards, including 13 Car of the Year awards, both in Northern American and in Europe. It was also included in Car and Driver magazine’s Ten Best List from 2000 through 2004 and recognized as the world’s best-selling car in 2001 and in 2002.

The Ford Focus was substantially upgraded in 2005 so there are only few changes to the 2006 Ford Focus model. The 2005 Ford Focus came with restyled Ford hood, larger Ford grille, reshaped Ford front fenders integrated with the Ford headlights. These new Ford parts were maintained for the 2006 model; however, Ford offers this time a new Street Appearance Package for Ford Focus ZX3, Ford Focus ZX4, and Ford Focus ZX5, laden with safety and convenience features.

Ford Focus Street Appearance Package came with different front and rear fascias, adding new Ford lights(Euro Altezza); lower Ford air deflector, Ford spoiler and rear Ford Front bumper; and chrome exhaust tip. The S and SE trim levels got optional alloy Ford wheels. All these additional features gave the new Ford Focus a racing car look.

Continuing success of the Ford Focus only reaffirms Ford’s renowned excellence in creating vehicles of extraordinary performance, interior and exterior auto parts. Also it further proves Ford’s high standards on quality automobiles and its commitment to the customer’s ultimate satisfaction.
Because of this, manufacturers and dealers of aftermarket and replacement Ford parts like the country’s top quality Ford auto parts supplier, Ford Parts Online, feel the need to continuously raise their quality standards as well in order to meet higher demands of Ford car users and match the latest from Ford.

At one time or another, you would need to replace some auto parts in your Ford Focus or any other Ford vehicle, whether it’s simply for maintenance, for repair, for car enhancement or customization. No matter how well built and how well designed your Ford is, it is still subject to some car problems and of course, you can make it better.

Replacing your OEM Ford auto parts has never been easier than it is today. There are thousands of aftermarket auto parts dealers all over the country and even online. You can have access to virtually all of them in just a click on a mouse, making it more convenient on your part. However, you still have to choose what is best for you. Even if many offer rock bottom Ford Parts Discount deals, you are not guaranteed to get the best for your Ford.

Choosing a trusted and experienced auto parts dealer like Ford Parts Online can save you from worries. This auto parts dealer offers a great variety of Ford replacement and aftermarket parts including the finest line of Ford Explorer parts, Ford Mustang partsFord F-150 Pickup parts and Ford Escape parts. Sourced from well recognized Ford parts manufacturers, you can be sure that these parts meet the industry’s highest standards for car parts. Priced like Ford Parts Used, its Ford Parts Discount are the perfect answer to your high quality and inexpensive Ford replacement part needs. Ford Parts Discount

by: Jay Stevens

Read More......

"My Motorcycle won't start!! What now?"

Maintain your Battery and check your charging system!

9 times out of 10 the reason why your bike won't start is usually because of the battery condition or loose connections. A charging system failure is less likely but is still possible.

I will talk about both of them here.

First look at your battery connections. Check for obvious and easiest to fix problems first. A loose connection, poor ground etc. will likely cause intermittent operation of the starting and charging systems. If you find a loose connection and/or corrosion, clean the connections with a wire brush.

Before re-attaching apply a little grease to the contact points. The grease helps to prevent any of the white corrosion residues building up around the battery terminals.

Try and start her up now. You still have a problem? Go down to the mall and buy yourself a small electronic multimeter. (Make sure it has both AC and DC volt functions, as well as a continuity (or OHMS)function. Pull out the battery and set it on a counter. Set your multimeter to DC volts. Measure the Battery voltage by placing the red lead on the positive and the Black on the negative.

The voltage read should be around 12.5 volts (higher is OK) If the voltage is less than this it may indicate a poor battery. Notice I say, "may" here because the bike's charging system might be at fault. In this case the battery will most likely be OK.

Confirm that the electrolyte level in each cell of the battery is good. Add distilled water only to cell's with a low level. (Obviously you cannot add water to a maintenance free battery) Charge the battery overnight with a slow charger only. Motorcycle batteries cannot handle a fast charge. Make sure the charger only charges at a rate of 2 amps or less.

Install the battery and try and start her again. If she still won't go buy a new battery and your problem will likely be fixed. If she starts and runs like a charm, then you have to find out why the battery went dead. You need to check the charging system.

With the engine running, place the multimeter leads on the battery. Rev the engine a little. The system voltage should rise with engine RPM. A voltage of around 13.5 to about 14.5 should be displayed. If the voltage stays constant and/or is slowly decreasing, or if the voltage rises above 14.7 volts the charging system is not functioning.

What do you do now? You have to check two things. The Stator and the Regulator. The stator creates an AC voltage. The regulator changes the AC to DC voltage and also maintains that voltage at the proper level.

The Stator can be checked with the Ohms function on your meter. Locate and remove the plug for the stator on the front of the engine block. You will see two or three pins inside.

Set the meter for low Ohms, and measure the continuity between these pins. 5 Ohms or less is what you are looking for here. Set the meter to the highest setting. With 1 lead attached to a metal part of bike check for continuity to each pin. You meter should read infinite, or no continuity. If these tests check out then your stator is fine. If there is a fault in any of these tests, then see your dealer

The regulator is the easiest of all to check. The regulator is made of solid state electronics and can't be opened. Replace the regulator if everything else on the charging system checks out or if there is an overcharging situation.

On most Harley's you will not know if the charging system is beginning to fail. The evidence shows up when you have dim lights or she just won't start. There are aftermarket accessories that you can install on your bike that will tell you the current state of the charging system.

Save yourself some bucks here!! With a simple multimeter available from any Electronics parts store you can troubleshoot your charging system and check your battery and most likely repair any problems yourself.

by: Keith

Read More......

Mountain Dirt Bikes

What are ?

Mountain dirt bikes are basically dirt bikes for use in climbing and descending rocky and grassy mountains. They can be motor or peddle models and it is up to you which you go for. The motor versions are quite different in design and look to other dirt bikes because of the use they are designed and built specifically for.

How do mountain dirt bikes differ from other dirt bikes?

Specifically, the frame is a lot higher than on a standard dirt bike in order that you get more ground clearance; the extra ground clearance will help you avoid mud build-ups, rocks and other such debris when traversing a mountain or hill. The frames themselves are also much more sturdy so if you do happen to clip a rock or something similar they are unlikely to just snap in half and will provide you and your bike with more protection. The brakes are stronger, making it possible to stop your bike rolling down the hill or off a rock and they usually come with both rear and front suspension to make the trickier terrain associated with mountain riding easier to handle. The suspension also makes the ride a lot more comfortable because you will face a number of bumps and sometimes some quite manic descents down the mountain.

Generally speaking a mountain dirt bike is much more rugged and rough than a normal dirt bike because of the beating and battering it will take during it’s life.

What else should I know about my mountain dirt bike?

If you own or are considering purchasing a mountain dirt bike you should know that you can’t purchase normal dirt bike parts and expect them to do an equally good job on your mountain dirt bike. They simply aren’t designed for the same purpose. Yes, it’s true that a dirt bike is built to withstand quite a battering and a beating but it’s also designed for riding around a dirt track. However, a mountain dirt bike is designed to be ridden over mountains and through rocky, grassy and muddy terrains. The tires are such that they can withstand all of these terrains as is the rest of your bike. The suspension, brakes and frames are quite different when compared to other types of dirt bikes so you should be careful when buying parts or repairing your bike.


by: Andrew Green

Read More......

Sites To Help You In Car Buying Online

With everything virtually possible, why not car buying online?

In fact in the past years, car buying online has evolved from tips and comparison charts to honest-to-goodness online transactions. Gone are the days when you have to personally scout for your dream car, hopping from one store to another, talking to car dealers and comparing prices.

Now, buyers can go online and do all this and more… that is if you know where to look in the World Wide Web. Here are some sites that will help you make car buying online as easy as shopping for grocery. So click away and take that virtual shopping cart.

The comparison strategy

Web sites like AutoVantage allows users to look at several models, their specifications and features and to compare them with each other. It also gives you an idea on what specific car model suits your needs, lifestyle and of course the budget. Car buying online has never been easier as websites like these allow for clearer and faster comparisons as you are given prices and features at the drop of the hat. There are also resources on the site that would help you answer those frequently asked questions about car buying online.

Price is the name of the game

If you have already been car buying a few weeks now and know the model that you want, you can check your dream car’s prices online before going to different car dealers and haggling. The InvoiceDealers.com is a site that gives you competitive prices that you can choose from. You no longer need to visit several dealers as this site makes car buying online or even offline a breeze.

Virtual loans and finances

Who says you can only avail of financial arrangement through face to face transactions? With the advent of super technology, car buying online has become a one-or-two clicks activity. One useful site is the E-loan, which offers loans and other financial arrangements. The site also contains various resources that would help people who are car buying online for the first time.

Insurance at your fingertips

Believe it or not, you can put insurance arrangements in your virtual cart when buying a car online. What is more, you can compare the prices of the plans being offered by several insurance companies. When buying a car online, you can try the site, 4insurance.

Delivery a click away

Another consideration when car buying online is the delivery. Some websites offer instant delivery where the car of your choice will be delivered to your home and office. If you are not comfortable purchasing a car that you have not yet seen or examined, you can arrange to have it picked up instead. One site that has this feature is CarsDirect.com.

Saving on warranty

Warranties are really important whether you are car buying online or offline. This is especially true when you are buying a model that you have not yet tried using in the past or a model that you are totally unfamiliar with. Doing your research and scouting for an extended car warranty online can actually save you up to 60f the actual cost since this is usually sold direct. For prices for extended warranties, you can visit Warranty Direct.com, which offers several quotes.

by: John G. Nuble

Read More......

Simple, Fast and Affordable Ways to Enhance Your Chevy Available at Your Friendliest Auto Parts Dealer

Since man developed fondness for automobiles, the auto industry just grew bigger and more diversified. Almost every stage in the history of cars is marked by an invention, an introduction of a new design or car concept and a whole lot of new ideas aimed at improving car's performance, style and safety features. Likewise, replacement auto parts market has thrived due to the growing demands of auto users. Hence, today, more choices of high quality auto parts and even accessories are available for your car repair, car maintenance and customization.

Auto Parts Discount is one of your top auto parts dealers that bring to you a wide selection of replacement parts from BMW parts to Ford parts, Jeep parts, and GMC parts . If you have an old car, whether it's an old Chevrolet Impala or an old Ford Mustang, this store can help you make your car livelier and more fun to drive. Accessories ranging from floor mats to different kinds of specially designed auto lights, mirrors, carpets and spoilers can be easily purchased in its convenient, safe and complete online store. These are all sourced from top car part manufacturers and are designed to match your car's specifications.

It's easy to upgrade your old Chevy and modify its looks at Auto Parts Discount. You can start it by replacing your car's carpet or floor mat. Even if your Chevrolet carpet or your Chevrolet floor mats aren't that old yet, they need to be replaced periodically since dirt and grime often get stuck in them. Especially if the stitching of your old Chevrolet carpet has already been badly frayed, you need to replace it now or else be very uncomfortable. It always feels good to have something neat, smooth and comfortable to step on as you ride inside the car, so make sure you replace your Chevrolet carpet with a good quality carpets.

Other Chevrolet parts offered here in this one-stop auto parts dealer online are Chevrolet lights like headlights, taillights and corner lights, Chevroletmirrors and Chevrolet spoilers. Aside from their known functionality, these auto parts help in improving your car's styling. Auto lights for example make your car extra attractive as they provide bright illumination at night while spoilers make your car look like real sports cars.

Making your old car more exciting to drive need not be financially burdensome. All you need is some imagination. Auto parts like the auto bumpers , carpets, lights, car wheels , mirrors, spoilers and catalytic converters can bring more life to your everyday driving. These are very affordable accessories that you can easily purchase online. Visit Auto Parts Discount and enjoy their wide variety of parts including accessories for Chevrolet—all at very friendly deals you'll surely love.

by: Joe Thompson

Read More......

Simple Car Maintenance Tips

You drive your car everyday. Do you pay attention to it? Do you feel that slight shimmy in the front end? Is there a new knocking sound under the hood? Is there a rattle in the dashboard? No one knows your car better than you do. If you feel something different, or if it isn't handling correctly take it to your mechanic. It could be something as simple as a tire out of alignment, or perhaps a loose belt. It's always best to find any small problem before it becomes a large one.

Here are some simple maintenance tips that you can follow to help prolong the life of your car, and help save you money.

Notice where you park your car and get into the habit of looking to see if there are any leaks when you pull out. This can be very tricky in a public garage with lots of stains from leaks from other cars, but if your car is leaking any type of fluid, transmission, radiator or brake the leak will look "fresh". If you see any fluid leaking have your car serviced as soon as possible.

Keep an eye on your tires. When you have your oil changed every 3,000 miles have your tires rotated. At this time the technician will inspect your tires for any wear. Keep your tires aligned. Check your tire pressure once every month. It's easy enough to read tire gauges and they even have electronic ones. Keeping your tires properly inflated helps increase gas mileage too.

As mentioned above, change your oil at least every 3,000 miles. The oil is the life blood of your car and keeping fresh oil in your car can extends it's life by many, many miles. At this time the technician will check your air filter, hoses and belts.

Keep your windshield washer reservoir full and carry an extra gallon with you. You don't want to be caught without washer fluid, and you don't realize how quickly you use it up, especially in the winter months when we get salt spray on the windshield. Replace your wiper blades once a year.

Following these simples steps can go a long way in prolonging the life of your car.

by: Simon Harris

Read More......

Should you keep your old car or buy a new one.

Are you sure you need a new car? I'm sure you want the newest safety features and modern styling that a new car offers. Perhaps you need a larger vehicle to fit your growing family. You probably feel that your old car no longer fits your life. But how about cost?

From an economic perspective, you're better off keeping your old car. It could save you thousands of dollars. Taking better care of your current car may make much more sense in the long run.

You're probably thinking - those repair bills are really adding up. But the cost of repairs will never exceed the cost of a new car. Changing your oil, replacing brakes, belts, and hoses are nothing compared to monthly payments on a new car. Even costly repairs like rebuilding an engine makes good financial sense.

If you've paid off your car, it is still in great shape and needs only a few modest repairs, there's no need to throw it away. Enjoy your freedom from car payments. Enjoy lower annual taxes, insurance rates and license fees on your old car. Buying a new vehicle would mean several years more of monthly principle and interest payments on a loan.

You can feel secure knowing that modern vehicles last longer. Not too many years ago, a vehicle's useful life did not exceed 100,000 miles. Today, many vehicles can breeze right past that 100,000 mile mark with no more than a tune-up, or maybe a new timing chain or fuel pump.

Older cars generally cost more to maintain and are more likely to break down. Repairs can be frustrating and expensive. But on the other hand they're cheaper to own and operate. They lose most of its value in the first five years of their life. Your used vehicle won't depreciate as much, saving you thousands.

Unless you're rolling in cash, I'd say keep your old clunker. Comfort yourself knowing that one day you'll be able to easily afford that costly new ride.

by: Roger Charles

Read More......

Shopping for your Motorcycle Parts Online with less effort

If you are among those who spend most of your day attending to your motorcycles, indeed you are considered to be called a motorcycle enthusiast. These people would exchange their important appointments and dates just to buy more time with their motorcycles. That’s pretty fanatical I guess.
Some people really exert all their efforts in maneuvering their bikes. Some even have treated screws, wedges and other tools like their meals and food for the day. There are some who love motorcycles but only for the means of traveling and easy riding to escape themselves from heavy traffic over big busses, trucks and cars. As you can see, motorcycles are small and can fit on thin spaces in the streets.
Motorcycle lovers care for their bikes like caring for their own selves. They would even spend loads of money for maintenance, upgrades and repairs. For them, buying motorcycle parts is like buying clothes for themselves. I think that’s precisely what you call dedication and more like it.
Some purchase motorcycle parts as if they were dressing their motorcycles for a display, some rather for good performance and sound. Upgrading your motorcycles is indeed helpful. Finding new parts with good quality for your motorcycles is keeping up its power and performance. Since it is important, one must carefully be inclined with knowledge in choosing the right parts and brands.
These motorcycle parts can be acquired and purchased in hardware and motorcycle stores. Nowadays, shopping for your motorcycle parts can be purchased online. I can say it can be advantageous to shop online because it requires less work and you don’t have to waste efforts from going from one store to another only to find out that the parts you are looking for are unavailable or the stocks are all out.
With shopping online for your motorcycles, you are sure you get the most certain parts your bike needs and it gives you ideas on the price listings and some important information and details. Shopping online for your motorcycle parts gives you other options for varieties of selections. It is also to your advantage because it has wide connections or it is worldwide so don’t feel sad if the parts you are vying for are not available in your country. It can still be at your hand without any extra effort.
If you want to upgrade on an extensive level, shop online for a change and plunge in to your motorcycle addictions. It might cause to add a little extra cost but it’s worth it. You don’t have to work yourself way out on the stores. All you need is a computer and let them easily do it for you with no burden at all.

by: Karen Nodalo

Read More......

Save Thousands at Auto Auctions - Without Marrying a Car Dealer!

The Common Misconception: Auto auctions are only open to car dealers.

The Surprising Truth: Anyone with the right resources can participate in the same auctions as the dealers!

Think about it. How much could you save if you bypassed the dealers and purchased directly from their sources? 30%, 50%, maybe even 75%.

As unbelievable as this sounds, it is possible with a little patience and research.

As you probably already know from past experience, car dealers will do ANYTHING to get you into the car of your dreams. Whether you can afford it or not!

I can recall a former coworker who got into a new luxury vehicle with a little "creative financing." The manager divided his mortgage payment in two. His justification: As a married man his wife was responsible for the other half of the mortgage....even though she was a stay at home mom! Luckily for them, they found a way to pay their huge car payment and avoid repossession.

Unfortunately, others aren't quite as lucky. Thousands of people default on their loans everyday simply because they couldn't really afford it in the first place.

This can work to your advantage. The banks and financial institutions that serviced the loans want to recoup their loss as quicly as possible. Add to that the exhorbitant cost of storing these vehicles, and you can easily see why the banks want to dispose of them in a timely manner.

After all, the longer financial institutions have to store these vehicles, the less money they're going to get back.

Auto auctions are the quickest way for banks to rid themselves of repossessed vehicles.

Car dealers know this, and they go to great lenghts to protect this knowledge from the general public. After all, auto auctions are a huge source of revenue. Dealers can purchase vehicles at a fraction of their value, and then resell them at a huge mark-up.

But what if you could avoid the dealer's mark-up and instead pay what they pay? What impact would that have on your wallet?

Amazingly enough, auto auctions are not solely restricted to car dealers. Up until a few years ago, I too shared this common misconception.

It was only by sheer luck that I stumbled upon a website that allowed me to search local auctions by zip code and vehicle make that I learned the surprising truth. I was paying dealers thosands of dollars in unnecessary mark-ups.

I tried the website's search feature out, and to my surprise the cars listed were exactly what I wanted. Only a few years old with very low miles. Many of them were still under the manufacturer's original warranty! This made sense of course, since most of them were repossessions.

The auction house was even willing to throw in a vehicle history report at no extra cost and a 3 month warranty.

Sure I wouldn't get the complimentary car washes and oil changes the dealer throws in, but that surely wasn't worth thousands of dollars in premiums.

After a little hesitation I joined the auto auction membership site. They helped me locate auto auctions in my area, and gain admission to them through their exclusive access rights. I learned what questions to ask, and how to handle the bidding process.

It was a lot simpler then I ever imagined it could be.

The day of the auction, I showed up a few hours early to inspect the vehicle I was interested in and get a feel for the place.

It must have been a slow day, because when my car came up for auction only a few dealers were bidding against me. Since I wasn't buying the vehicle for resale, I succeeded in outbidding the dealers!

It was a truely empowering experience. I got the vehicle of my dreams, and I only paid a little over half its book value!

What did this experience teach me? Auto Auctions can save you thousands in unnecessary dealer mark-ups.

by: Cat Tobin

Read More......

Save Money on Used Motorcycle Parts

For every motorcycle enthusiast, it is indeed very taxing to maintain bikes as good as new – its engine running and all its other parts functioning. We know for a fact that it’s not only for the sake of transportation but also for a little satisfaction of our vanity – seeing everyone admire us, atop an excellent piece of machine. Like any road going vehicle, a motorcycle's performance is based on the smooth running of thousands of parts, large and small. It is a nuisance indeed to find some faulty parts on a vehicle and prevent owners from enjoying its full use.

Broken parts on a motorcycle can spell tragedy for its driver and extensive damage to the machine. In a motorcycle, the safety and security provided by a four wheel vehicle on each corner doesn't exist as such, when its rear wheel locks up at 70 mph it could skid out of control and throw its rider. What’s more heartbreaking is to know that the cause of the accident is because of a broken part.

The best solution is to always have a replacement part handy in order to have extra parts for those which have been damaged or lost. Having ample budget for this would, however run risks for your pocket. If you do not have sufficient budget to afford the high costs of brand new replacement parts but afraid of scratching around for used motorcycle parts from questionable origins and warranty, don’t fret. There’s still a way for you to save money by buying used motorcycle parts and prevent you from living your worst nightmare.

Yes, indeed! Buying used motorcycle parts are a great way for you to save money and keep your bike going splendidly. There are just some pointers or guidelines for you to remember once you have decided that your budget leaves you little choice between brand new and used motorcycle parts. By following several general guidelines, you could still acquire used motorcycle parts that are in tip top shape, good condition and will not be the cause of your bike getting torn apart.

First of all, when scouting for used motorcycle parts, especially online, make a point to double – check, there are things to look out for, consider and avoid. Don’t ever miss out on crucial details, like, how old can the used part be? How compatible will it be to your bike’s model and make? Next, it is understandable to be skeptical, after all, the World Wide Web is full of BS and scams. You have to be careful to avoid those who make stupid claims that expect you to believe them. It is but your right to verify and countercheck the validity of everything that they are offering you and once you have placed an order, as much as possible, give certain conditions for your purchase. Something that may go like, they will have to show you if the purchased part functions upon getting secured on your bike. You could also inquire for warranty periods.

There are ways to save your money and still get above-average used motorcycle parts. Just be wise enough once you decide to be practical and economical.

by: Lala C. Ballatan

Read More......

Save at the Gas Pump - Real Money Saving Tips

Real Money-Saving Steps

There are numerous no- or low-cost steps you can take to combat rising gas prices.
Most cars can run on regular unleaded – 87 octane. High performance vehicles will usually require 91 octane or higher. Check your owner's manual to determine the right octane level for your car. It’s also usually written inside your gas lid, door panel, and sometimes right on your dashboard under the fuel gauge. It will say something like “Premium Unleaded Only” which means 91 octane or higher. All gas pumps must post the octane rating.

Gas Cards

Check out gas card offers from gas stations and credit card companies. The can save you an additional 1% to 5% off every gallon or earn you free gas. One of the best cards out there right now can be found http://valueauthority.com/savegas.htm

If you put 20 gallons in your car at $3.00 per gallon, that’s $60. A 5% cash back would save you $3.00 making your effective cost per gallon just $2.85. It’s like getting a free gallon of gas with every fill up!


Drive more efficiently:

-- Stay within posted speed limits. The faster you drive, the more fuel you use. For example, driving at 65 miles per hour (mph), rather than 55 mph, increases fuel consumption by 20 percent. Driving at 75 mph, rather than 65 mph, increases fuel consumption by another 25 percent. This is caused by the amount of energy it takes to push your car through the air and the amount of drag created by your cars body.

So if your car gets 25-mpg highway at 55 mph, driving 65mph will drop it down to 20 mpg! Driving 75 mph drops it down to just 16 mpg!

My personal experience with my 98 VW Beetle: I drove to New York at the posted speed limits between 55 and 65 mph. I got about 35mpg and 450 miles on one tank!!! When I drove to Florida the posted speed limits were between 55 – 70 mph. I actually drove about 75 mph most of the way. I only got 27 mpg and about 350 miles on one tank. I lost almost 100 miles distant per tank! I couldn’t believe it.

-- Use overdrive gears. Overdrive gears improve the fuel economy of your car during highway driving. Your car's engine speed decreases when you use overdrive. This reduces both fuel consumption and engine wear. Most automatic transmission cars will have an overdrive button right on the gearshift. Look for a “D” and/or “O/D”. You will see a light on the dash indicating weather it’s on or off. Check your owner’s manual to be sure. If your car has a tachometer, you should be able to tell by watching your engine’s rpm speed on the highway. Buy switching the overdrive on, your rpm’s should drop significantly.

-- Use cruise control. For longer trips using cruise control can help you maintain a constant speed and, in most cases, reduce your fuel consumption. Set it to 55 mph on highways.

-- Avoid unnecessary braking and acceleration, and improve your fuel economy by 5 to 10 percent. In city driving, nearly 50 percent of the energy needed to power your car goes to acceleration. Go easy on the gas pedal and brakes. "Jack-rabbit" starts and sudden stops are wasteful. Let off the gas early when approaching yellow and red lights, stop signs etc… Most fuel-injected cars will cut off the fuel supply to the engine while you slow down saving you even more gas.

-- Combine errands. Several short trips taken from a cold start can use twice as much fuel as one trip covering the same distance when the engine is warm. It takes about 15 to 20 minutes for a car to reach normal operating temperature. Until then, your car is using almost twice as much fuel to keep the engine running!


-- Remove excess weight from the trunk. Avoid carrying unneeded items, especially heavy ones. An extra 100 pounds in the trunk reduces a typical car's fuel economy by one to two percent.


Maintain your car

Keep your engine tuned. Studies have shown that a poorly tuned engine can increase fuel consumption by as much as 10 to 20 percent depending on a car's condition. Follow the recommended maintenance schedule in your owner's manual; you'll save fuel and your car will run better and last longer.

-- Keep your tires properly inflated and aligned. Under inflated tires on a car is like running on the beach with no shoes. Car manufacturers must place a label in the car stating the correct tire pressure. The label usually is on the edge of the door or doorjamb, in the glove box, or on the inside of the gas cap cover. If the label lists a psi (pounds per square inch) range, use the higher number to maximize your fuel efficiency. Under inflated tires cause fuel consumption to increase by 6%.

-- Change your oil. Clean oil reduces wear caused by friction between moving parts and removes harmful substances from the engine. Change your oil as recommended by the vehicle manufacturer.

-- Check and replace air filters regularly. Your car's air filter keeps impurities in the air from damaging internal engine components. Not only will replacing a dirty air filter improve your fuel economy, it also will protect your engine. Clogged filters can cause up to a 10% increase in fuel consumption. Imagine running up a flight of stairs with only using one nostril in your nose to breath.

Gas Cards

Check out gas card offers from gas stations and credit card companies. The can save you an additional 1% to 5% off every gallon or earn you free gas. One of the best cards out there right now can be found http://valueauthority.com/savegas.htm

If you put 20 gallons in your car at $3.00 per gallon, that’s $60. A 5% cash back would save you $3.00 making your effective cost per gallon just $2.85. It’s like getting a free gallon of gas with every fill up!

by: Robert Rogers

Read More......

Researching Vehicles Online

The purchase of a new car is a serious investment. It is best that you do your homework before purchasing a new vehicle, to avoid ending up with a vehicle thats overpriced or just not right for your needs. Luckily, with the help of the internet, you can do all of your research directly online from the comfort of your home.

Your first goal should be to figure out what type of vehicle is right for your family. Are you looking for a sports car, or do you have children and need a sedan, minivan or SUV? You need to consider how many seats you need and how much storage space for cargo.

With todays rising gas prices, you may want to opt for the most fuel efficient type of vehicle. In other words, carefully compare the difference in gas mileage between two types of vehicles before choosing the one thats right for you. A sedan will likely use much less gas than a minivan, and if you dont need the extra seats or cargo room, you can save a significant ammount of fuel cost over the lifetime of a vehicle. Minivans and SUV's use similar ammounts of gas, depending on the size of the vehicle. A mini SUV may be a good choice over a full size SUV, saving you money every time you fill up at the pumps.

After you know what type of vehicle you are shopping for, you can focus on a make and model. Be sure to read reviews from existing owners, they often times can save you from purchasing something that isnt going to make you happy.

There are many excellent consumer review sites on the internet that have a wealth of information on what owners like and dislike about their vehicles.

Here are a couple of sites to get you started:
http://auto.consumerguide.com
http://www.edmunds.com

Many auto review sites also offer price guides so that you can know in advance what the vehicle of your choice is likely to cost you. Also, auto makers often offer price quotes directly from their sites. You can also find additional information, pictures, and sometimes video at the auto makers sites.

Once you have done all of your research, selected the make an model of the vehicles you are interested in, you can then go to your local dealership armed with all of the information necessary to make an informed buying decision. By researching vehicles online, you can save time, money and gain piece of mind.

by: Amber Lowery

Read More......

Repairing Your Own Machine Components

Many industrial concerns have workshops of their own. For the repair of worn shafts, the lathe machine is excellent. Keyway slots can be machined by using a milling machine, while a shaping machine can do machining of large flat areas. A drilling machine does drilling of holes.

A skilled Maintenance Engineer should know how to use all these machines in order to make his own repairs in a safe manner. Very often he has to supervise machinists. The information below should be useful for that purpose.

Lathe Machine

The lathe machine uses a single-point-cutting tool for a variety of turning, facing, and drilling jobs. Excess metal is removed by rotating the work piece over the fixed cutting tool to form straight or tapered cylindrical shapes, grooves, shoulders and screw threads. It can also be used for facing flat surfaces on the ends of cylindrical parts.

The work piece is clamped onto a horizontal rotating shaft by a 3-jaw or 4-jaw chuck. The latter chuck can be used to cut off-centered cylinders. The rotating horizontal spindle to which the chuck is attached is usually driven at speeds that can be varied.

The cutting tool is fixed onto a tool rest and manipulated by hand. It can also be power driven on straight paths parallel or perpendicular to the work axis. This is useful for screw cutting.

Internal turning known as boring results in the enlargement of an already existing hole. The holes are more accurate in roundness, concentricity, and parallelism than drilled holes. A hole is bored with a single-point-cutting tool that feeds along the inside of the work piece.

Shaping Machine

The shaping machine is used to machine flat surfaces, grooves, shoulders, T-slots, and angular surfaces with single-point tools. The cutting tool on the shaper oscillates, cutting on the forward stroke, with the work piece feeding automatically toward the tool during each return stroke.

Drilling Machine

The drilling machine is used to cut holes in metal with a twist drill. By changing the cutting tool, they can be used to do reaming, boring, counter boring, countersinking, and threading.

Milling Machine

The milling machine uses a rotating cutting tool to cut flat surfaces, grooves, and shoulders, inclined surfaces, dovetails, and T-slots. Cutters of many shapes are changed to cut different grooves.

Cutting Tools

Metal-cutting tools are classified as single point or multiple point. The lathe and shaping machine use single point cutting tool while the milling and drilling machines use multiple-point-cutting tools.

Metal is cut either by moving the work piece like in the lathe or by moving the tool like in the shaping machine, drilling or milling machine. Clearance angles must be provided to prevent the tool surface below the cutting edge from rubbing against the work piece. Rake angles are often provided on cutting tools to cause a wedging action in the formation of chips and to reduce friction and heat.

Tool Materials

In order to remove chips from a work piece, a cutting tool must be harder than the work piece and must maintain a cutting edge at the temperature produced by the friction of the cutting action.

Carbon Steel

Carbon steel tools even though comparatively inexpensive tend to lose cutting ability at temperatures around 400 degree F (205 degree C).

High-Speed Steel

High-speed steel, containing 18 percent tungsten, 4 percent chromium, 1 percent vanadium, and only 0.5 to 0.8 percent carbon, permits the operation of tools twice or three times the speeds allowable with carbon steel

Cast Alloys

Cast-alloy cutting-tool materials containing cobalt, chromium, and tungsten are effective in cutting cast iron and retaining their cutting ability even when red hot.

Cemented Tungsten Carbide

The hardness of Tungsten Carbide approaches that of a diamond. Tungsten carbide tools can be operated at cutting speeds many times higher than those used with high-speed steel.

Oxides

Ceramic, or oxide, tool tips consist primarily of fine aluminum oxide grains, which are bonded together. These are very hard.

Cutting fluids

An overheated tool can become blunt and soft very fast. Therefore very often, cooling fluids cools the cutting points of the tool. This serves to lubricate and cool.

Water is an excellent cooling medium, but it corrodes ferrous materials. Sulfurized mineral oil is one of the most popular coolants as it can both cool as well as lubricate. The sulfur prevents chips from the work from melting on to the tip of the tool.

by: Thomas Yoon

Read More......

Tips For Keeping Up With Automotive Recalls

You hear about automotive recalls all the time in the newspaper, on the Internet, as well as on the nightly news. Amazingly, one in 12 cars traveling the roads today were recalled for one reason or another in 2003. However, even more amazing is the fact that only one third of the owners of the recalled vehicles chose to take their car in for the needed repairs. The car manufacturers are required to send out letters informing owners of these vehicles of the recall, regardless of whether it is a major or minor event. Also, the information regarding the recall is delivered to consumers in so many different mediums it is almost impossible that owners of the affected vehicles do not learn of the problems. However, people seem to think that if they are not experiencing any problems at the moment then the recall affects all of the other vehicles instead of theirs and end up ignoring the recall. This is negligence and simply asking for the problem with the car to crop up. However, if this happens after the recall then it is the owners fault because they were given the information and allowed to fix the problem free of charge yet they simply ignored it. As long as car manufactures report the recall and inform owners of the vehicles as they are required to do by law, it is up to the consumer to take advantage of the recall and have their automobile fixed. If not, then the owner is taking the risk. If you have not heard anything about car recalls or just bought a used vehicle and want to find out if the manufacturer issued any recalls then you should check out www.nhtsa.gov or www.autorecalls.org to see if your car is listed.

Both of these websites have all the information about recalls over the past years so you can search through the year, make, and model of a vehicle to see if yours is listed. It is very likely you will see your car listed on one of these website because more than 31 million cars were recalled in 2004. That is almost unbelievable considering the amount of technology used in developing cars as well as the fact that cars are safer than they have ever been. However, it is true that mistakes are still taking places and consumers are buying vehicles with basic problems like fuses or major problems with gas lines, tires, and seats buckling in crashes. Regardless of whether or not you believe you are driving a safe car you need to check out the websites stated above every few months just to make sure your vehicle has not ended up on the list. If it has, don’t fall into the two thirds of individuals who never respond to the recall. Instead, head to the nearest dealership or authorized mechanic who can make the free repairs to your vehicle. Why so many people don’t have time for free repairs is beyond me, but knowing your vehicle has a problem that could be potentially fatal for you and your family and that a free repair is available should be enough to motivate you to have the repair taken care of.

Another thing to keep in mind is that simple problems with your vehicle that result in a visit to the mechanic may not be a problem you are required to pay for. Millions of Americans each year take their cars to the mechanic for a basic repair, or even a major one, assuming something went wrong and they simply need to fix it. Unfortunately, many of these individuals never check to see if the problem was due to a recall and end up paying for a repair that might be free or discounted by the automobile manufacturer. So, armed with this knowledge the next time your vehicle has even the slightest problem make sure you check and see if the car has been recalled for similar problems and if you can get free repairs or discounted ones at the least. It is certainly worth checking out and could save you hundreds or even thousands of dollars.

Who Issues Recalls?

In general, the reason so many people don’t respond to recalls is because they simply don’t understand the recall process. The NHTSA , National Highway and Traffic Safety Administration, is responsible for investigating consumer complaints regarding specific vehicles and problems associated with them. After several consumers have reported the same or similar problem to the NHTSA for the same model vehicle an investigation is launched. The point of the NHTSA investigation is to determine whether the consumer caused the problem or malfunction in some way or if the manufacturer of the vehicle is at fault. If the manufacturer is determined to be at fault then the owners of affected models will receive information in the mail regarding the recall of the vehicle with information included on how they can have the problem corrected free of charge. However, the NHTSA is not always the one who issues a recall.

Occasionally, the manufacturer realizes a problem exists in a certain model vehicle and will voluntarily issue a recall. Of course, the NHTSA is informed as well, and the same letter is sent to owners of the vehicle letting them know the problem with the vehicle and how to correct it. Many times, however, a recall does not affect all models of a particular year. For example, if a recall is issued on 2005 Ford Explorers more than likely it will only affect a certain batch of these vehicles and not all of them. However, if you own a vehicle of that make and year then you can take it to the dealership and the service department will run the VIN, or vehicle identification number, to determine if in fact your vehicle is affected by the recall. If so, then you can have the repairs made at no cost. If not, then you can head home knowing your vehicle is safe and sound.

Just keep in mind, however, each year millions of cars are recalled for various reasons and you should always take your car in if you suspect the recall might apply to your vehicle or if you receive a recall letter. Don’t take your safety for granted, especially if the repair for the recalled vehicle is free.

by: Jeff Dragt

Read More......

Timing belts, the sleeping time bomb

Interference Engines: ……..Free Useful informatio

When buying a used car always insist on determining if the vehicle has a rubber timing-belt. Be aware that about five years ago an International Oil Company did a follow up on 5,000 cars it had turned back after 3 year leases and traced them to their eventual private owners. All the cars had by then passed through wholesale auction markets and likely one or more retail dealers before being sold to a private owner. The survey disclosed that 50% of the cars had their odometers illegally turned back.

When buying a used car, supposedly with 40,000 miles for example, and determining it has a rubber timing belt, insist on a written guarantee from the seller to guarantee in writing to replace the timing belt at no charge if it fails within another 20,000 miles, a typical recommended total amount (Call any Dealer to get the recommended amount for the particular make of vehicle). After all, the vehicle may in fact already have 55,000 miles on it. If the seller will not make that guarantee, then he is admitting that the mileage is probably not accurate and by implication may well have been turned back. If the seller will not make that guarantee, consider a compromise, such as $100 maximum cost. If not acceptable, walk away and look elsewhere."

Before buying any car, especially 4-cylinder foreign cars, or even 6-cyl. BMW, be aware of the unavoidable cost of $400-$800 to replace the timing belt at anywhere from 50,000 to 70,000 miles if the car has an 'interference' type of engine. The sales person will invariably not mention that an 'interference' type engine powers the vehicle and may not even know what one is. If a timing belt on an interference engine is not replaced at recommended intervals, the repair cost when the belt breaks (not gradually, but always catastrophically) could increase to $3,000 to $5,000 due to engine failure because parts have smashed into each other

An 'interference' engine is an engine design that has been avoided by some manufacturers for well over 80 years. General Motors, Chrysler, etc., typically use a metal chain-type timing belt on push-rod engines (often called a timing chain) to transmit torque from the engine crankshaft o the engine camshaft that opens the valves that admit air and fuel. (Note: on some new cars the fuel is admitted not through the valves but through injectors in the top of the cylinder. Rather than use a steel timing chain, interference engines may use a rubber timing belt with its limited life, whereas steel timing belts typically last 150,000 to 200,000 miles or more.

Valves open further in an interference engine and project further into the combustion chamber than in a 'free-running' engine. This allows outside air at atmospheric pressure flow faster into the combustion chamber through the larger valve opening. The engine can therefore inhale more air, be a little smaller, and still create as much power while reducing its. manufactured cost and also guaranteeing future repair business for its dealer. If a rubber timing belt breaks by not being replaced soon enough, some of the valves stuck in their open position will collide with the top of the pistons, thereby breaking or irreversibly damaging one or the other or both. To make matters worse, it is not possible to measure the wear on such a rubber belt so that it could be replaced when there is some indication of imminent failure. Failure in these belts is catastrophic, without warning. This will require a whole new engine be installed. Woe to the owner. Finally, the rubber belt may have to be replaced long before 60,000 miles solely due to its age. This is really playing a bad poker hand. Interference engines are like a time bomb waiting to explode unless replacing the timing belt at the recommended interval. Be aware of that guaranteed future expense before buying a new car, or especially a used car, " with such an engine.


by: Ralph Hoffmann

Read More......